BGP route reflectors
Route reflector is an IBGP feature that allows you to build scalable IBGP networks. The original BGPv4 contained no intra-AS loop prevention mechanism; routers were therefore prohibited from sending routes received from an IBGP peer to another IBGP peer, requiring a full-mesh of IBGP sessions between all BGP routers within an AS.
Route reflector functionality (defined in RFC 4456) adds a new attribute (cluster list) which can detect route propagation loops within an AS, the full-mesh requirement is thus significantly relaxed.
Route Reflector rules
A BGP router implementing route reflector functionality propagates BGP routes according to these rules:
- Locally originated routes and routes received from EBGP neighbors and selected as best routes are propagated to all BGP peers (internal and external).
- Routes received from an IGBP peer that is not a route-reflector client and selected as best routes are propagated to all EBGP peers and all IGBP peers configured as route-reflector clients.
- Routes received from a route-reflector client and selected as best routes are propagated to all BGP peers (internal and external).
Whenever an IBGP route is reflected (propagated to another IBGP peer), the route reflector appends two optional, non-transitive attributes to the BGP route:
- If the route does not have the Originator ID attribute (it has not been reflected before), the router ID of the IBGP peer from which the route has been received is copied into the Originator ID attribute.
- If the route does not have the Cluster list attribute, it’s added to the route.
- The value configured with the bgp cluster-id router configuration command (or the router ID of the route reflector if the cluster-id is not configured) is prepended to the Cluster list attribute.
Route reflector does not change or remove any other attributes of the reflected routes (even non-transitive attributes), ensuring that the IBGP routes are not changed within the autonomous system.
Monitoring Route Reflection
The route reflector-related BGP attributes attached to a BGP route can be inspected with the show ip bgp prefix command:
Edge#show ip bgp 10.2.2.0 BGP routing table entry for 10.2.2.0/24, version 12 Paths: (1 available, best #1, table default) Flag: 0xA20 Not advertised to any peer 65001 10.0.1.1 (metric 129) from 10.0.1.3 (10.0.1.3) Origin IGP, metric 0, localpref 100, valid, internal, best Originator: 10.0.1.1, Cluster list: 10.0.1.3
The same command will also indicate whether a route was received from a route-reflector client (and will thus be reflected to all IBGP peers):
RR#show ip bgp 10.2.2.0 BGP routing table entry for 10.2.2.0/24, version 18 Paths: (2 available, best #2, table default) Multipath: eBGP iBGP Flag: 0x1A20 Advertised to update-groups: 1 65001, (Received from a RR-client) 10.0.1.2 (metric 65) from 10.0.1.2 (10.0.1.2) Origin IGP, metric 0, localpref 100, valid, internal, multipath 65001, (Received from a RR-client) 10.0.1.1 (metric 65) from 10.0.1.1 (10.0.1.1) Origin IGP, metric 0, localpref 100, valid, internal, multipath, best
The route propagation policy of a route reflector is also displayed in the show ip bgp update-group printout:
RR#show ip bgp update-group BGP version 4 update-group 1, internal, Address Family: IPv4 Unicast BGP Update version : 22/0, messages 0 Route-Reflector Client Community attribute sent to this neighbor Extended-community attribute sent to this neighbor Update messages formatted 59, replicated 47 Number of NLRIs in the update sent: max 1, min 0 Minimum time between advertisement runs is 0 seconds Has 2 members (* indicates the members currently being sent updates): 10.0.1.2 10.0.1.4 BGP version 4 update-group 2, internal, Address Family: IPv4 Unicast BGP Update version : 22/0, messages 0 Community attribute sent to this neighbor Extended-community attribute sent to this neighbor Update messages formatted 5, replicated 0 Number of NLRIs in the update sent: max 1, min 1 Minimum time between advertisement runs is 0 seconds Has 1 member (* indicates the members currently being sent updates): 10.0.1.1
Loop Detection and Avoidance
The BGP routers implementing original route reflector RFC (RFC 1966) use the following mechanisms to detect route-reflector-related loops:
- If the Originator ID in an incoming IBGP route update is equal to the BGP router ID, the update is ignored (reflected route was propagated back to its originator).
- If the Cluster ID of a route-reflector appears in the Cluster list attribute of an incoming IBGP update, the update is ignored (route reflector loop).
The route reflector functionality was introduced in IOS release 11.1. It’s therefore relatively safe to assume that every Cisco router encountered in a production network supports it.
Although the mechanisms specified in RFC 1966 ensure loop-free IBGP operation regardless of the actual topology of the IBGP sessions, RFC 4456 added new route selection rules that improve the actual convergence within an AS and reduce the amount of BGP updates propagated across the AS:
- Routes with shorter Cluster list attribute are preferred. This rule ensures that all routers select routes with minimum number of reflections, significantly reducing the amount of unnecessary BGP updates (remember: only best routes selected by a route reflector are reflected to its clients).
- The Originator ID attribute of a reflected route should be used as the Router ID attribute when comparing otherwise identical IBGP routes, ensuring the stability of route selection across AS regardless of the route reflectors.
Route Reflector Design Rules
Traditional design rules recommended a hierarchy of redundant route reflectors or an IBGP full-mesh between route reflectors.
With the improved IBGP loop avoidance, you could use more relaxed designs, ranging from route-reflector-client being configured on every IBGP neighbor to designs where the edge routers act as route reflector clients and all other BGP routers in the AS act as route reflectors.
Cluster-ID is Obsolete
Cisco IOS implementation of route reflector functionality supports the bgp cluster-id parameter, which is used in the Cluster list attribute instead of the Router ID. The cluster-id parameter is useful in redundant route reflector scenarios where multiple route reflectors serve the same set of clients, but can lead to partial connectivity when multiple IBGP sessions are disrupted.
The revised BGP route selection rules ensure that a route reflector in a cluster always prefers route from a client (with shorter Cluster list) over a reflected route, thus making the bgp cluster-id parameter obsolete. You should not use the bgp cluster-id in new designs to increase the resilience of your network.